Herringbone block paving driveway with kiln-dried sand brushed into the joints
Jet washing

Block paving cleaning and sealing

Cleaned, re-sanded and sealed so the blocks stay locked together.

Block paving looks tired long before it wears out. Moss fills the joints, weeds push through, and the surface goes grey and patchy. We clean block paved drives, paths and patios across Coventry and the West Midlands, clear the joints, refill them with kiln-dried sand and seal the surface if you want it to stay cleaner for longer. You agree a fixed price before we start.

Over 13 years' experienceCoventry based, West Midlands wide
Free, fixed quotesAgreed before any work starts
Free site visitBefore every build quote
We clear up afterWaste taken away, site left tidy
Herringbone block paving driveway with kiln-dried sand brushed into the joints

Why block paving needs more than a jet wash

Block paving works because of the sand in the joints. It locks each block against its neighbours, so the whole drive spreads the weight of a car instead of individual blocks rocking and sinking.

Any clean that is strong enough to shift moss will also move some of that joint sand. Leave the joints empty and weeds move straight back in, water gets under the blocks, and over time you get loose or sunken areas. That is why our block paving cleaning always ends with re-sanding.

Weed and moss removal from the joints

We start by raking and scraping weeds and moss out of the joints and along the edging. Getting the roots out before the wash means they are not pressed back into the gaps.

The surface is then cleaned with a rotary surface cleaner that keeps the pressure even across each block. Edges, around manhole covers and against walls get a hand lance. Oil and tyre marks are pre-treated where they will lift. Finally the slurry is rinsed off so it does not dry back onto the blocks.

  • Weeds, grass and moss cleared from joints and edges
  • Even clean across the whole surface to avoid stripes
  • Extra attention around drains, covers and kerbs
  • Debris swept up and taken away

Re-sanding with kiln-dried sand

Once the blocks are dry, we brush kiln-dried sand across the surface and work it down into the joints. Kiln-dried sand is fine and completely dry, so it flows to the bottom of narrow gaps instead of clumping at the top the way damp builder's sand does.

We sweep it in, let it settle and top it up until the joints are full. The surplus is swept off. It sounds simple, but the timing matters: the blocks have to be properly dry, which on a cold or damp day can mean waiting, or coming back. We will not rush the sand into wet joints.

Block paving sealing: is it worth it?

Sealing is optional, and we will tell you honestly whether your drive will benefit. A sealer soaks into the surface and binds the top of the joint sand, which makes it harder for the rain and the next clean to wash it out and harder for weeds to seed in the joints.

It also makes oil spills and general dirt easier to wipe away, and some sealers bring the colour of the blocks back up. The trade-offs are that it adds time, needs a dry spell either side, and will need redoing in future as it wears. How long it lasts depends on the product, the weather and how much traffic the drive gets.

Clean and re-sandClean, re-sand and seal
Joint sandRefilled, can wash out over timeRefilled and bound at the surface
Weeds and mossCleared, will slowly returnCleared, slower to return
StainsCleaned offCleaned off, new spills easier to remove
Weather neededDry enough to sandDry before and after sealing
Back on the driveUsually same dayAfter the sealer has cured

When block paving needs more than a clean

Cleaning shows up the condition of a drive. Sunken areas, usually where a car wheel sits or near a drain, often point to a weak sub-base underneath. Cracked blocks and loose edging are also easier to spot once the dirt is gone.

We will point out anything we find. Small issues are best dealt with before sealing, because a sealer locks in whatever is underneath it. Our driveway cleaning page covers other drive surfaces, and if you have a block paved patio out the back, see patio cleaning.

Does pressure washing harm block paving?

Done badly, it can. A narrow nozzle held close to the joints blasts the sand and can mark the face of the blocks. Done with a rotary cleaner at a sensible pressure, followed by a proper re-sand, it does no harm. Our guide on whether pressure washing damages block paving goes into the detail.

We clean block paving right across the West Midlands from our Coventry base, including plenty in Birmingham and Solihull.

How it works

What happens, step by step

  1. Get a quote

    Tell us the size of the area and whether you want it sealed on our quote form.

  2. Clean

    Joints cleared, surface cleaned evenly, stains treated and slurry rinsed away.

  3. Re-sand

    Kiln-dried sand brushed into every joint once the blocks are dry.

  4. Seal if chosen

    Sealer applied in dry weather. We tell you when it is safe to drive on.

What is included

  • Weed and moss removal from joints and edging
  • Pre-treatment of oil and tyre marks
  • Rotary surface clean plus hand lancing of edges
  • Re-sanding of every joint with kiln-dried sand
  • Optional sealing once the blocks are dry
  • Sweep-up and waste taken away
Questions

Block paving cleaning and sealing FAQs

What sand do you use to re-sand block paving?

Kiln-dried sand. It is fine and completely dry, so it runs right down into narrow joints and fills them from the bottom up. Damp building sand clumps at the top and leaves gaps underneath.

How long after cleaning can block paving be sealed?

The blocks and joints need to be properly dry first. In summer that can be the same day or the next. In cooler, damp weather it can take longer, and we will come back rather than seal onto a wet surface.

Does sealing stop weeds completely?

No sealer stops every weed for good, but binding the joint sand makes it much harder for seeds to take hold. Weeds and moss come back more slowly than on an unsealed drive.

Will sealing make my block paving shiny?

That depends on the sealer. Some leave a natural matt look, others a satin or wet look that darkens the colour. We talk you through the options before we start.

Can you fix sunken blocks while you are there?

Our job is the clean, re-sand and seal, not relaying paving. If we find sunken or loose areas, we will point them out, because they usually mean a problem with the base underneath and are worth sorting before any sealing.

How often should block paving be re-sanded?

Whenever the joints have visibly dropped or after a deep clean. Checking the joints once a year and topping up low spots keeps the blocks tight.

Herringbone block paving driveway with kiln-dried sand brushed into the joints
EVC Jetwash and Landscaping

Get a fixed price for the job

Tell us what you need and we will come back with a free quote.

Free quoteCall us