Half-cleaned patio showing the difference jet washing makes to dirty paving slabs
Jet washing

Jet washing across the West Midlands

Drives, patios and decks cleaned properly, joints re-sanded.

EVC has been jet washing drives, patios and decks for over 13 years. We are based in Coventry and work right across the West Midlands, from Hinckley to Wolverhampton. We clear the moss, algae, oil and weeds, put fresh sand back in the joints and take the mess away with us. Tell us what needs doing, and you get a fixed price before we start.

Over 13 years' experienceCoventry based, West Midlands wide
Free, fixed quotesAgreed before any work starts
Free site visitBefore every build quote
We clear up afterWaste taken away, site left tidy
Half-cleaned patio showing the difference jet washing makes to dirty paving slabs
Our approach

A clean that doesn't leave the drive worse off

Anyone can hire a pressure washer. The difference is knowing how much pressure each surface takes, and what has to go back afterwards. Block paving loses joint sand, sandstone scars if you get too close, and softwood decking furs up under a narrow jet.

We use rotary surface cleaners for even results on open areas, a hand lance for steps and edges, and treatments where they help. On block paving, every job finishes with a re-sand in kiln-dried sand, and block paving sealing is there if you want the joints to stay put longer.

We also think about where the water goes. Dirty water is rinsed towards a border or gravel, not straight into the road drain, and the moss and grit is swept up and taken away.

Quick facts
  • Over 13 years' jet washing experience, based in Coventry.
  • We cover the whole West Midlands, from Hinckley to Wolverhampton.
  • Block paving is always finished with kiln-dried sand in the joints.
  • Every job comes with a fixed price agreed before we book.
  • Drive and patio can be cleaned on the same visit, with one tidy-up.
  • We sweep up and take the waste away.

Which clean suits your surface?

SurfaceHow we clean itAfter the clean
Block pavingRotary cleaner, joints cleared firstRe-sand with kiln-dried sand, optional seal
Concrete and imprintedFirmer clean, stain pre-treatmentWe flag tired sealer on imprinted drives
TarmacLow pressure, keep movingNo harsh chemicals
Indian sandstoneModerate pressure, rotary cleanerOptional treatment to slow regrowth
PorcelainQuick surface clean, joints checkedUsually nothing further
Timber deckingLow pressure along the grainLet dry before any oil or stain

What we clean

Our jet washing covers the hard surfaces around your home. Most customers book a drive or a patio, and plenty book both on the same visit to save a second trip.

Each service has its own page with the detail on how we approach it: driveway cleaning, patio cleaning, block paving cleaning and sealing and decking cleaning.

  • Block paved, concrete, imprinted and tarmac driveways
  • Indian sandstone, porcelain, limestone and concrete slab patios
  • Paths, steps and side passages
  • Block paving re-sanding and sealing
  • Timber and composite decking

Signs your drive or patio needs a clean

Most drives and patios go green sooner or later, especially in shady spots by fences, hedges and trees. These are the signs it is time for a clean.

Our guide on how often to clean your driveway goes into the timing in more detail.

  • Green or black film that makes the surface slippery when wet
  • Weeds and moss growing up through the joints
  • Joint sand dropped below the top of the blocks
  • Oil drips or tyre marks on the drive
  • Black spots of lichen across sandstone or concrete
  • Steps that feel risky in wet weather

Pressure washing done properly

Pressure washing gets a bad name because it is easy to do badly. A narrow nozzle held close to the surface strips out joint sand, etches soft stone and leaves stripes. Done right, it is the quickest and most effective way to get a hard surface clean.

We match the method to the surface. Rotary surface cleaners keep the jets an even distance from the paving, which gives a consistent finish and keeps spray low. Sandstone and timber get lower pressure. Limestone never sees acidic cleaners. Tarmac is cleaned gently, especially in warm weather when it softens.

Worried about your blocks? Our guide on whether pressure washing damages block paving explains what goes wrong and how we avoid it.

Re-sanding and sealing block paving

Block paving depends on the sand in its joints to lock the blocks together. A deep clean will move some of it, so we always finish block paving by brushing kiln-dried sand into every joint once the surface is dry. Kiln-dried sand is fine and dry enough to run right to the bottom of narrow gaps.

Sealing is the optional extra. A sealer soaks into the blocks and binds the top of the joint sand, so it resists washing out and weeds find it harder to take hold. It needs dry weather before and after, and we will tell you honestly if your drive would benefit.

Jet washing from Coventry across the region

Coventry is home, and we work right across the West Midlands from there: Solihull and Shirley, Birmingham and Sutton Coldfield, the Black Country towns, out to Redditch, Bromsgrove, Lichfield, Tamworth, Hinckley and Stratford-upon-Avon. Our town pages, listed below, cover each area.

Every job is priced up front. Send us a few details and photos through our quote form, and we will agree a fixed price before booking. If you have questions first, have a look at our FAQs or get in touch.

How it works

From first question to signed off

  1. Tell us what needs cleaning

    Use our quote form to tell us the surfaces, rough sizes and send a photo or two.

  2. Fixed price

    We agree one price for the job before we book a date. No extras on the day.

  3. Clean

    Joints cleared, stains treated, surfaces cleaned at the right pressure and rinsed down.

  4. Finish and tidy

    Block paving re-sanded, sealing done if you chose it, debris swept up and taken away.

What is included

  • Weed and moss removal from joints and edges
  • Pre-treatment of oil and tyre marks where it helps
  • Rotary surface clean matched to the surface
  • Hand lancing of steps, edges and corners
  • Re-sanding of block paving with kiln-dried sand
  • Optional block paving sealing
  • Sweep-up and waste taken away
Questions

Jet washing FAQs

How much does jet washing a driveway cost?

It depends on the size of the drive, the surface, how much moss and staining there is, and whether you want re-sanding and sealing. We give you a fixed price once we know the details, agreed before we book.

Do you need to use my water?

Yes, we connect to an outside tap. If you do not have one, mention it when you ask for a quote and we will talk through the options.

Will jet washing damage my block paving?

Not when done properly. We use a rotary surface cleaner at sensible pressure and re-sand the joints afterwards with kiln-dried sand, so the blocks stay locked together.

Do I need to be in while you work?

Not for the whole job. We need the cars moved, access to an outside tap and any side gates open. Many customers leave us to it.

Can you clean my drive and patio on the same day?

Yes, and many customers do. It means one visit and one tidy-up. Just include both when you ask for a quote.

Do you work in the winter?

Cleaning can be done most of the year, but re-sanding and sealing need dry weather, so those are easier to schedule in the warmer months. We plan around the forecast.

Half-cleaned patio showing the difference jet washing makes to dirty paving slabs
EVC Jetwash and Landscaping

Ready to talk about jet washing?

Answer a few questions and we will come back with a free, fixed quote.

Free quoteCall us